How to remove old wired security system

If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.

Log in or Sign up. DIYnot Forums. Removing old ADT alarm system Hi, Ive got an old ADT alarm system in my flat, the contract expired a long time ago before we moved in, I do not want an alarm system at the moment. There are lots of old wires and sensors that I want to remove. Can anyone recommend a good method of removing the system. Will the alarm go off if I cut the wires going into the mains box?

Photographs attached to my profile. Any help, much appreciated. Thank you. To remove the alarm you need to remove the mains power, remove the alarm casing, and disconnect the big battery terminals. Beware that doing any of the above should activate a tamper alarm which will sound until you have removed both sources of power, or until you enter a code with the appropriate access level. However they're not as complicated as they are made out in my opinion for a competent DIYer.

Why not replace only the brain - they're not very expensive. Most of the wiring is numbered the same from your existing box as to a new replacement. I used one from the same manufacturer to make it easy for me tho. There's a possibility the alarm wont go off anyway as ADT fit decoy boxes a lot of the time.

The sounder in the endstation may sound though. Be careful doing as advised above unless you REMOVE the fuse from the spur before opening the box or you could touch live volt wires. Thank you for both your replies. Very helpful. Just to confirm. Turn off mains. Remove casing 3. Disconnect Battery 4.Thanks for your subscription! These days, I frequently stumbled on questions asked by new homeowners whether they can use or upgrade the existing security system or wired alarm system kits when they move into a house with home security or alarm systems in place.

How can I monitor these systems myself on my phone? Many of us, quite often, bought or moved into a house that has an existing security or alarm system kits such as ADT or Honeywell wired security system or a place that comes with an unmonitored home security system. Some are still configurable and you might accidentally arm it and set it off every now and then, toying with ideas that you might reconfigure or reprogram it to put it into good use or upgrade the alarm system by integrating with new systems.

While some of these old security systems might have been in idle for years but the cables remain in good shape.

How to Safely Remove a Wired Security System

In many scenarios, the existing security system could be used to power new home security cameras or security systems, for example, connecting Cat5 Ethernet cable to CCTV security cameras. It's crucial knowing what you can do with existing or pre-wired home security system when moving into a house with an existing alarm or security system, especially potential benefits and risks. If the existing alarm security system is still in good shape, whether it's a hardwired alarm system or wireless alarm system.

For example, a new ADT security system with cellular monitoring or landline monitoring or Honeywell security systems, signing up for the monitoring service with the monitoring service providers or companies seems like a reasonably nice way to shore up your home security. Using or customizing the existing infrastructure, such as PIR motion detectors, smoke detectors, heat sensors, glass break detectors, external sirens not only cut the cost of installation and equipment, minimizes troubles of running wires or installation but also help reduce monitoring burden if you are not interested in self-monitoring and prefer professional monitoring.

However, before going down this road, it's wise to give some thoughts to these questions, does the company has a good track record of satisfactory service and support? Do they provide all the services that you are looking for? To avoid getting stuck with an alarm company that provides unsatisfying services, take the checklist below into account:.

Upgrading the existing security system to something that can be monitored via phone apps seems like a feasible solution if you don't want to be locked into a contract, paying monthly monitoring fees or having your house monitored by someone else.

Also note that some used alarm systems are still bound to valid contracts with monitoring service providers. So, if you convert home security system to self-monitoring without offering proper notices to those companies, they may require penalty and even give you bad credits. To avoid such troubles, you'd better cancel home security contracts properly ahead of the conversion. We have rounded up some of the feasible methods to convert wired alarm systems to self-monitoring ones:.

how to remove old wired security system

Add a control panel: If you are looking for a control panel to integrate to your existing wireless system that uses Z-Wave, Zigbee, Insteon, X10, UPB, or A10 technology and turn it for self-monitoring, we suggest reaching out to the manufacturers first to see what options do you have. Convert wired alarm systems to wireless ones: Here is a step by step guide on how to switch your DSC system to be Wi-Fi enabled with notifications and monitoring from a phone. Integrate with smart home devices: You can DIY the existing wired home security system and use existing equipment and turn it into an unmonitored security system and integrate into your home automation by using SmartThings Smart Home Hub or HomeSeer.

Here is an enthusiastic entrepreneur dedicating himself to converting the wired alarm system into a SmartThing smart home monitoring system. Turn analog systems to IP security systems: If the home security cameras are in a good working order but you might just want to remotely access the security cameras, you could upgrade the analog system into an IP security system.

Takeaway: You may also refer to this helpful guide for more solutions to activate, monitor, and upgrade existing alarm security systems. And join the discussions on upgrading existing security or alarm systems in many forums, such as Reddit. It neither can be re-activated to continuously monitor your entrances nor does it have features like Smartphone-based control, home automation potentials, phasing it out and replacing it with new and modern security cameras or systems goes a long way in protecting your property.

Especially those are packed with advanced mobile app controls, wireless sensors, or high-resolution HD smart security cameras capable of motion detection like Reolink Argus 2 wire-free cameraface recognition, motion tracking, or smart home integration like IFTTT, Alexa voice control or command.

Takeaway: Check out this post to learn more benefits and features of self-monitoring security systems. No matter what option you choose, there are various factors that you might need to weigh on when moving into a house with pre-wired or existing security systems.

Supposed that the existing alarm systems at your home have been put into use for less than 5 years, they may still function well without outdated features and you may continue using them to secure your home. If you keep using over year-old alarm systems, chances are high that the alarm systems don't work properly from time to time and the monitoring companies charge your extra repair fees since the surveillance equipment is too old.

Moreover, some used analog security systems may not integrate with new IP security cameras and modern smart home devices as well. If the systems are over 10 years old, it is best to consider their lifespans and features and decide whether to replace them or not.Hello, We purchased our simply safe alarm months ago but we still have not installed it due to having to deal with removing the hard wired system we already have. We canceled our service with our provider when we got the Simply Safe system and we unplugged the transformer but we're not sure how do we go about taking down the hardwired keypads and motion sensor?

We really want to start using our Simply Safe system but we have to get the old one off the walls first. Does anyone have any suggestions?

Thanks, Crystal. Good morning Crystal. Having to deal with the evil empire myself ADTthis topic is right up my alley. Note if you don't have ADT it will apply to almost any of the traditional national companies. First, make sure you carefully read your contract.

In most instances you don't own the system, the alarm company does. You are legally required to return it.

Once its down, call them advise you want to have them pick it up. ADT asked me "why did you take it down? It could increase your home's resale value? When I told them it was already down, they told me to "throw it out as it wasn't worth it for them to get it back"!! I sent them a certified letter, return receipt, saying they had thirty 30 days to pick it up at my house at a mutually agreed time. It was in the garbage in 31 days. I will spare you the billing issues AFTER I legally cancelled my contract for the sake of time, but now onto your question about removal.

First, all of the components are of course hard wired and screwed into the wall. For some components, I was able to use a small flat blade screwdriver to pry off the cover of the motions. In those instances where successful, unscrewed the back with the faceplate off, and then put it in a box.

how to remove old wired security system

Pushed wires back through the wall, spackled and then painted. For those components I could not pry open the face, I used a very sharp sheet rock knife and cut around each component. Then used a large, flat blade screwdriver and and pulled off wall. The cut around the sensor prevented tearing. Wires pushed back in the wall, stuff in newspaper, insert piece of new sheetrock into the hole left, tape, spackle, sand and paint.

The main box, unplug the power, then cut all alarm wires and toss in your holding box. Now every square foot is covered with SS's low prices and ease of installation. And make sure if you had any "in frame"s sensor in door frames, be careful of water. When they drill through your frames wood rot will often happen.

I actually left my two ADT sensors in the frame and then used a lifetime clear caulk to cover them. Playing some good music while you are removing the sensors helps the process go more quickly. For full disclosure, my wife had all the rooms repainted over the past 3 years as she said the paint matching was only so so. I think it was just an excuse but who am I to argue with my better half.

Wow, thank you so much for that detailed response! I really appreciate it! I will remember all of your advice when I take the system down today! Also I cancelled the contract maybe five months ago so I think I'm okay with that!Removing a Brinks alarm system can be done by canceling service with Brinks and asking it to remove its equipment from your home you may be charged for this. Because the removal of Brinks security equipment isn't difficult, it can easily be done my most people.

Always cancel your service first; otherwise, Brinks will suspect that an intruder is tampering with the system. Locate the main control unit. Remove it from the wall. Depending on the model of the control unit, this can be done by removing the main cover from the panel and then unscrewing the mounting screws underneath.

The main cover usually has clips that can be popped off from the bottom of the unit. Remove the batteries from the control unit. The control unit has batteries in case of a power failure. Locate the power wire from the control unit. This will be labeled. Follow the power wire until the power source is reached. Typically, the unit is plugged into a power outlet located in another room.

This is done for security reasons. Unplug the unit from the power source once you find it. Unplug all other wires that connect to the control unit. Most sensors and monitors are powered by battery and not through the main unit.

However, some older models may still be wired. Remove the sensors from the doors and windows. Go to every door and window in the house and remove the magnetic sensors from them. Use a glue solvent to ensure that the adhesive doesn't remove paint when the sensors are pulled off. Remove motion-sensor devices. These are typically screwed into the house or affixed with a strong adhesive. Unscrew or use a glue solvent to remove any motion sensors. Remove any smoke or CO2 detectors that were associated with the Brinks security system.

Smoke detectors are either screwed in or stuck with adhesive to the ceiling; CO2 detectors are typically just plugged into the wall. Replace CO2 and smoke detectors immediately after the Brinks ones are removed. Erick Kristian began writing professionally in He has a strong background in business and extensive experience writing fiction and articles related to spirituality and self improvement which are published on growingeveryday.

Kristian has written several screenplays, produced numerous films, published books and written numerous articles on a variety of subjects.

how to remove old wired security system

Hunker may earn compensation through affiliate links in this story. Things You'll Need Household tools Glue solvent. Brinks offers different types of protection systems. Step 1 Locate the main control unit.

Step 2 Remove the batteries from the control unit. Step 3 Locate the power wire from the control unit. Step 4 Unplug all other wires that connect to the control unit.

how to remove old wired security system

Step 5 Remove the sensors from the doors and windows.This week I posted an update on twitter and facebook of my latest project where I took all the wired window and door sensors from my old security system and integrated them into SmartThings. Many people said they want to do the same thing and I know that my usual step-by-step spoon-fed tutorial was in order.

When I purchased my home last year, I had a tough decision to make. We were going to do a lot of renovations and I had to decide whether to keep the existing alarm system or just rip it all out. The alarm system was installed in the early 90's and the plastic keypads and motion sensors that were installed in the walls had turned yellow from sun damage.

I spent a week researching how to replace everything because it didn't make sense to rip out a perfectly good security system, but finding replacement parts proved impossible. I ended up disconnecting the power and back up battery, removing the keypads and motion sensors, and letting the contractor cover all the holes with drywall.

However, all the contact sensors within the doors and windows were still there and in-place. In hindsight, I should have kept it. The first thing we have to do is lay down an initial requirement. It's pretty cheap to get started with home automation, but it can get expensive quick.

Car Alarm Keeps Going Off - How To Fix It

I finally found myself with a few hours of spare time and decided to look into integrating the door and window sensors into SmartThings. After a few hours of research, spending a long time reading comment threads, buying equipment and waiting for delivery, I was able to have it fully integrated. It's awesome to give this old technology new life. So lets do this! Your security system may have been segmented out into zones for doors or windows to belong to a certain "zone".

Of course, this is also going to depend on how many devices you have. The example we are going to use for this tutorial will not have any motion sensors, sirens, etc. It's going to only be the contact sensors, which are very simple to use. One thing you may notice on the old security system is that there are resistors that limit the amount of power making a loop on each circuit.

This was necessary on the old system because the sensors may have been ruined if too much current was running through them. However, it's your choice to keep or remove them with this new setup. I opted to remove them because the Arduino will be responsible for sending a low voltage signal through the digital GPIO pins and doesn't need an Ohm resistor.

It will keep it cleaner. The wires going into your panel may or may not be labeled to which device they lead to. Mine were not. For me to properly wire everything, I needed to test each circuit and see what the wires were leading to.

To test it, we need to load a Sketch on the Arduino. You can also go ahead and place the SmartThings board onto the Arduino. Look at the pin numbers to make sure they line up. Pin 1 on the Shield lines up with Pin 1 on the Arduino, etc. Grab 2 jumper wires. Go to tools and set the type of Arduino to Mega.

Create a new Sketch by copying and pasting this code taken from parralax. Hit the upload button.Removing a home security system can be done easily without causing damage to any of the wiring or existing circuits. Here are some simple tips that will help you if you need to remove an older security system. If you currently have a monitoring service, you want to make sure you contact them before you start disconnecting parts.

Many monitoring services will automatically dispatch police if a wire is cut or power is lost to the service. Another feature of most alarm systems is that a siren is placed on a separate circuit. This way, if a would-be intruder decided to try to cut the power to the alarm system, the siren will still sound.

What to Do with Existing/Wired Home Security/Alarm Systems

It usually sounds automatically as well if the system detects an interruption in the power supply. Not only will you want to disconnect the power from the security system, but you will also want to locate the siren circuit and disconnect it as well.

The control panel is the brain behind the security system. Once all of the other components have been removed you can pull the panel down. Behind the panel, you will find wiring. If you are upgrading an existing security system, you may not have to remove the old battery pack. If the battery pack is still in good condition, it may be salvaged as part of the upgrade.

The battery pack can be found behind the control cabinet for the system. Be sure to remove the black and red wires that feed into the pack if you are removing the entire thing. With the power disconnected, you can start to remove other components associated with the system.

This can include any motion detectors, glass break sensors, and cameras. Some of these components will be installed with screws, and others such as window detectors will be installed using a basic adhesive.

If you have a hard time with an adhesive component, rubbing alcohol can be used on a cotton swab to break apart the glue. If you are upgrading to a newer system, leave the wiring in place and allow the new alarm company to determine if they can use the wiring. Nine times out of 10 they will be able to use this.

We welcome your comments and suggestions.

How to Remove a Home Intercom System

All information is provided "AS IS. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use.

View our Privacy Policy here. Toggle navigation Login Register How-Tos. Written by Sage C. Reviewed by Charles Ouellet. What You'll Need. Wire connectors Side cutter Screwdriver. Contact the Alarm Company If you currently have a monitoring service, you want to make sure you contact them before you start disconnecting parts.

Disconnect the Sirens Another feature of most alarm systems is that a siren is placed on a separate circuit. Pull Off Control Panels The control panel is the brain behind the security system.

Remove the Old Battery Packs If you are upgrading an existing security system, you may not have to remove the old battery pack. Remove Other Components With the power disconnected, you can start to remove other components associated with the system. DIY Hacks. Popular Articles. By Krystal Miller. How to Install a Wireless Home SecurityBe sure to follow all standard electrical safety procedures.

When working with electricity, it is always to test to ensure that a device has been disconnected prior to attempting to service it. Failure to follow these warnings can lead to shock or even death.

A home alarm system can provide security and piece of mind for you and your family. But, should you ever choose to remove the alarm system, you might be in for a big project depending upon just how far you want to go. Many alarm system components are unobtrusive and may be better left in place than removed. Some pieces however can be bothersome.

Removing them is generally just a matter of undoing the hanging mechanisms. Determine what components of the alarm system made be left in place. If the pieces are not in the way of other things and do not create visual problems, leaving them alone is preferable.

Once the "main" parts are removed, there is no downside to leaving the remaining pieces in place if they are not in the way. Notify the alarm monitoring company if there is one prior to disconnecting the alarm. Otherwise, it is likely that the police will respond to your home. Disable the alarm via the control panel. If there is a maintenance mode, put the alarm in maintenance mode. Disconnect power to the alarm and siren or horn at the circuit box. It is very important--in order to prevent electrical shock or even death--to use the multimeter or other testor to ensure that power is not flowing to alarm parts prior to attempting to handle or disconnect them.

Disconnect the power to the siren or horn. Removing alarm system components may trigger the alarm due to tamper resistance measures. Disconnecting the siren or horn first will prevent false alarms.

Examine the main alarm box. Generally, this is near one of the entrances. Determine if it is powered via battery or electrical wiring. Most electrically wired systems have a battery backup in case of power failure, so the presence of a battery does not mean that the system is battery-powered.

If the main alarm box is powered via battery, disconnect the battery first if possible. Then, remove any screws or nails holding the alarm box on the wall. If the box is adhered via a type of glue, it will be necessary to pry the box from the wall.

After all alarm control panels have been disconnected and removed, remove the remaining components such as opening detectors, motion detectors and glass break detectors via unscrewing or pulling nails.

Many detectors will be attached with adhesive. They can be removed by prying. Brian is a former certified financial planner, has experience in computers and technology, and is a MCSE. He has a degree in biochemistry from the University of Colorado.

Hunker may earn compensation through affiliate links in this story. Things You'll Need Handy Man's tools such as a screwdriver, pliers and hammer Multimeter or other tool for checking electrical current Ladder.


One thought on “How to remove old wired security system

Leave a Reply

Your email address will not be published. Required fields are marked *